- This topic is empty.
-
Posts
-
i setup a imaging system, all works, dhcp, bootp, tftpd after loading 6.3.0, 6.3.1 or 6.3.2 image files, it keeps telling me “unsupported firmware”loaded. frimware is not compatible.
i try to flash different s50 wyse thinclients.
what do i wrong?
any ideas ?
Looks like you are using the wrong firmware file. Could it be the one for V-class instead of S-class?
Tell us the correct name of the used .i2d file.CG
i tried the
5S50-5150-5S52_6.3.1_21-64 5S50.i2d 63 mb
5S52_REL_6.4.0_19-128 5S52.i2d 125mb
5150-5S50_6.3.0_36-64 5150.i2d 63 mb
REL_6.3.2_52-128 5S52.i2d 16.7 mb
OK, looks good so far.
What partnumber does your S50 has?
What folder in WSI have you used for the import?If the partnumber ends with -xxL you have a new RoHS compiant unit and have to use the S52 folder with S52 firmware. Otherwise use S50 folder and FW.
CG
the part number off my wyse is 902114-32l
the imported image firmware file is located
c:inetpubftprootRapportWyse5S506.3.1_63mb_6.3.1
wyse simple imagere log
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘sym/YES’ to ‘sym/YES’
Evaluating: ‘sym/YES’ to ‘sym/YES’
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘ftp//anonymous:[email protected]/Rapport/Tools/sa/5S50/push.k’ to ‘stream/sec/test’
Evaluating: ‘sym/YES’ to ‘sym/YES’tftpd log
Connection received from 10.1.1.14 on port 2070 [11/06 13:19:23.468]
Read request for file . Mode octet [11/06 13:19:23.468]
OACK: [11/06 13:19:23.468]
Peer returns ERROR -> aborting transfer [11/06 13:19:23.468]
Connection received from 10.1.1.14 on port 2071 [11/06 13:19:23.484]
Read request for file . Mode octet [11/06 13:19:23.484]
OACK: [11/06 13:19:23.484]
: sent 142 blks, 205431 bytes in 0 s. 0 blk resent [11/06 13:19:23.546]
Connection received from 10.1.1.14 on port 6000 [11/06 13:19:25.750]
Read request for file . Mode octet [11/06 13:19:25.750]
OACK: [11/06 13:19:25.750]
: sent 443 blks, 226624 bytes in 1 s. 1 blk resent [11/06 13:19:26.953]
Connection received from 10.1.1.14 on port 6001 [11/06 13:19:26.968]
Read request for file . Mode octet [11/06 13:19:26.968]
OACK: [11/06 13:19:26.968]
: sent 1 blk, 151 bytes in 0 s. 0 blk resent [11/06 13:19:26.968]That’s the wrong folder. Reimport the image 5S52_REL_6.4.0_19-128 5S52.i2d 125mb in S52 and try again.
CG
ok i will ,
now i get this error
CLIENT_AND_ARCHIVE_TYPE_CHECK’
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘sym/YES’ to ‘sym/YES’
Evaluating: ‘sym/YES’ to ‘sym/YES’
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘ftp//anonymous:[email protected]/Rapport/Tools/sa/5S52/push.k’ to ‘stream/sec/test’
Evaluating: ‘sym/YES’ to ‘sym/NO’
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘sym/NO’ to ‘sym/YES’
Evaluating: ‘sym/YES’ to ‘sym/YES’
Evaluating: ‘sym/CLIENT_AND_ARCHIVE_TYPE_CHECK’ to ‘sym/NOTFOUND’
Evaluating: ‘sym/YES’ to ‘sym/YES’IP address: 10.1.1.12
Subnet mask: 255.255.255.0
Default gateway: 10.1.1.254OK, that looks fine then.
How big is the flash size of the unit? It has to match with the size of the image.CG
first i have to thank you for your continuing support!
i found an newer simple imager instruction v3 that pointed out :
Note: A recent change in manufacturing to make our devices ROHS compliant, required us to use different hardware components and make changes to the software to
accommodate and recognize these components. To address this issue and to prevent any damage to the hardware with Wyse Simple Imager, new “Product Numbers” where added.
To avoid an “Incompatible Firmware†message, check the part number of your thinclient, and use the following table to cross reference your thin client model to the equivalent model to select under WSI 1.3.0 when “Adding” or “Submitting†the new firmware into WSI. This is only for the Sx0 and Vx0 series.i tried different part nummers and wsi model version but no luck.
how do i know the flash size of an s50?
- You must be logged in to reply to this topic.